In our andon lamp project, we showed you how to cut and assemble a lattice. This time, let's make one of its panels with kumiko.
What Is Kumiko?
Kumiko is a traditional Japanese woodworking technique that fits thin strips of wood together to form geometric patterns. It has long been used in fittings and decorations such as shoji screens and transom panels.
There are many kumiko patterns, including Asanoha (hemp leaf), Sakura (cherry blossom), Rindo (gentian), and Kagome (woven basket). By changing the shape and arrangement of the pieces, you can create a wide variety of patterns.

In this project, we'll use Japanese hand tools to make a kumiko panel in a square hemp leaf pattern. The standard hemp leaf pattern is built on a hexagonal grid, but here we'll make a square version that matches the shape of the panel so it fits into the andon.
For how to build the andon lamp itself, see:
Kumiko Lamp: How to Build a Japanese Andon with a Lattice
Materials and Tools
Materials
- Wood strips, 8 mm wide × 3 mm thick
- Wood strips, 8 mm wide × 2 mm thick
- Glue
The thickness of the pieces changes the look of your kumiko. Here, we used 3 mm stock for the lattice and 2 mm stock for the small pieces that go inside it.

Best Wood for Kumiko
Kumiko involves cutting thin pieces precisely, notching them, and fitting them together. Look for wood that's easy to work into thin strips and that resists splitting and chipping as you cut.
Harder woods can take more effort to work, which can make it difficult to cut thin pieces. On the other hand, wood that's too soft can be crushed as you work it or get dented when you fit the pieces together, so choose with care.
For this project, we used Japanese cypress, which is easy to work with.
Tools
-
Marking out: pencil, try square
-
Cutting and shaping: Dozuki Saw, 3 mm Oire Nomi Chisel, Hand Plane
-
Assembly and securing: masking tape, Wooden Mallet, small brush
-
Nice to have:
- Double-Blade Marking Knife: Lets you lock in a set width and mark two lines at once. It's handy for marking out many grooves of the same width.
Tools Used in the Kumiko Panel Project
Kumiko Tool Sets
Kumiko Woodworking Tool Set – 4 Pieces
Kumiko Marking & Cutting Tool Set – 2 Pieces
Dimension Drawing

Note: The dimensions in the drawing are for reference only and are based on the materials we used. They'll vary with the thickness of your wood and how it's been prepared, so please adjust them to fit your own materials.
How to Make a Kumiko Panel
Step 1: Make the Lattice
First, make a lattice sized to fit the andon panel (70 × 70 mm).
1. Cut the pieces
From the 3 mm stock, cut six 90 mm pieces for the lattice. Leave them longer than the finished size, since you'll trim off the excess after assembly.
Measure, mark your cut lines, and saw the pieces to length.

2. Mark the grooves
On each piece, mark three groove positions within a 70 mm span: one at each end and one in the center. Each groove is 3 mm wide, the same as the thickness of the wood.
Tape all six pieces together with masking tape so you can mark them in one go. A double-blade marking knife makes it easy to mark the same width again and again.
Also mark the groove depth on the side of the pieces so you know how deep to cut. The depth is 4 mm, half the width of each piece.



3. Make the saw cuts
Saw along the marking lines to cut the sides of each groove.

4. Chisel out the grooves
Use a chisel to remove the waste between the saw cuts and form the grooves.


5. Assemble the lattice
Remove the masking tape and fit the pieces together, alternating them so the grooves interlock. Tap them with a wooden mallet to seat them firmly.


Step 2: Make the Kumiko Pattern
Now it's time to make the kumiko pattern itself.
In kumiko, you create a pattern by angling the ends of each piece and fitting the pieces against one another. The square hemp leaf pattern we're making is built from three kinds of pieces. First, let's look at how the corners where the pieces meet are structured.
In this pattern, the pieces meet at 90° and 45° angles. Cutting these angles over and over by hand with no guide is hard work, so it helps to make angled jigs ahead of time.
Make each shaping jig at half the angle you want to create: a 45° jig for a 90° point and a 22.5° jig for a 45° point. We hope to show you how to make these jigs in a future article.


1. Diagonal pieces
Make four pieces to fit along the diagonals of the lattice.
Saw the wood to match the diagonals of the lattice. Then, using the 45° jig, pare both sides of the tip with a chisel or hand plane to form a 90° point. Shape the other end the same way so both ends match.
Fit each piece into the lattice and fine-tune it until it sits snugly.




Next, make the pieces that go inside the triangular frames formed by the diagonals. You'll need eight long pieces and eight short pieces.
Start by making one long piece and one short piece, and check their lengths against the actual frame. Then use them as a reference to make the rest.

2. Shape the long pieces
Each long piece is bent before it goes in. Measure to find the center and make a saw cut there.
Give each end a 45° point by paring with a chisel or hand plane against the 22.5° jig.




3. Shape the short pieces
The short pieces need a 90° point on one end and a 45° point on the other. Use the jig that matches each angle and pare with a chisel or hand plane.

4. Fit the pieces
Bend each long piece at its saw cut and fit it into the lattice. Then fit the short pieces. If a piece won't go in, pare its tip with a chisel or hand plane to fine-tune the fit.




Repeat these steps for every triangular frame, and your kumiko pattern is complete.


Step 3: Finish the Panel
Your kumiko pattern is now complete. Since this panel goes into an andon, the next step is to trim it to the panel size.
To keep the pieces from falling apart when you cut, take them all apart, apply glue, and fit them back in.
Once the glue is dry, saw off the excess so the edges are flush. Finally, fit the panel into the andon frame. If it's too tight, shave it with a hand plane until it fits.




Wrapping Up
In this project, we made a square hemp leaf kumiko panel and finished it as one of the panels of an andon. As you shape each thin piece and fit it into place, the geometric pattern gradually takes form. Use this guide as a starting point and try making other kumiko patterns, too.

Tools for Kumiko Woodworking
See the tools we used for this kumiko project in our kumiko tool collection.
Kumiko Tool Sets
Kumiko Woodworking Tool Set – 4 Pieces
Kumiko Marking & Cutting Tool Set – 2 Pieces